If a section on your multi-sensor display is not receiving a signal from the sensor, or the temperature is flashing, showing dashes, or is not updating, the unit may be experiencing wireless interference. Perform a hard reset to gain a strong connection between the units. 

Remove the affected Location from the display.

1. Press and release the color-coded button next to the location you want to delete from the display.
2. Press and release the “gear"  button.
3. Press and release the “▲“ or “▼“ buttons until “DELETE” is showing.
4. Press and release the “SET” button. “DELETE MONITOR” will flash.
5. Press and release the “SET” button to remove the location from the display.
6. Remove batteries from the remote sensor/monitor only. Do not power down the digital display.*
7. Wait 1 minute.
8. Reinstall the batteries in the remote sensor/monitor.

*If you are also using an add-on sensor such as the Water Detector, Liquid & Soil Temperature Sensor, or Spot Check Temperature & Humidity Sensor, please disconnect the add-on sensor from the monitor for one minute. Please reconnect the add-on sensor before reinstalling the batteries in the monitor.

Perform a Hard Reset:

1. Bring all the sensors and display unit together and remove batteries from the outdoor sensors. Make sure that the Wireless Reception Indicators on the display drop to zero bars to ensure that your display was connected to the correct sensors. (If your wireless reception indicator already indicates zero bars, please proceed to Step #2.)
   NOTE: If your display unit continues to show a strong connection, there is another sensor in your area that your display is connecting to (either a neighbor's or from another of your AcuRite units). If you have multiple sensors, make sure to use a different ABC channel on each. 
2. Remove the batteries and/or power adapter from the display unit.
3. Change the A-B-C switch on all sensors to a new channel, then press and hold the reset button for 20 seconds if applicable.
4. Reinstall the batteries in the outdoor sensors first.
5. Reinstall batteries and/or power cord into the display unit, then immediately press and hold the reset button again for 20 seconds if applicable.
6. Let the units sit within a couple of feet of each other for approximately 5 minutes or until you see a solid sensor signal.

Sync Sensors if they don't automatically connect:

To sync model 00275/00276 with a 06024/06036 display follow the steps below: 

Confirm the sensor is powered on with a reading on the display (model 02076RM) or the red light flashing every 16 seconds (02075RM)

1. Press and release the color-coded button next to a location on the display with the name “AVAILABLE.” Next, “ADD MONITOR” will flash at the top of the display. 
2. Press the “SET” button. “SELECT MONITOR STYLE” and (2) sensors will flash on the display. 
3. Press and release the “▲“ or “▼“ buttons to highlight the larger square sensor located on the right. 
4. Press the “SET” button to confirm your selection. “SELECT ID” appears on the display. 
5. Press and release the “▲“ or “▼“ buttons to cycle through the Monitors and/ or Sensors that the display has wirelessly identified. 
6. Press the “SET” button to confirm your selection. “SELECT NAME” appears on the display. 
7. Press and release the “▲“ or “▼“ buttons to cycle through the available location names. Select the name that most closely matches the location where the Monitor that is reporting data for the location is installed. 
8. Press the “SET” button to confirm your selection. The new Monitor will now synchronize with the display. It may take a few minutes for synchronization to complete.  

*To view the readings from an add-on sensor, press the corresponding colored button, then press the “▼“ button until "+Sensor" is displayed. The reading from the add-on sensor will appear in the Humidity section of that quadrant.

To sync model 00592TXR/06002M/06044M with a 06024/06036 display follow the steps below: 

Confirm the sensor is powered on with a reading on the display (model 06044M)  or the red light flashing every 16 seconds (06002M)

1. Press and release the color-coded button next to a location on the display with the name “AVAILABLE.” Next, “ADD MONITOR” will flash at the top of the display. 
2. Press the “SET” button. “SELECT MONITOR STYLE” and (2) sensors will flash on the display. 
3. Press and release the “▲“ or “▼“ buttons to highlight the narrow, tall sensor located on the left. 
4. Press the “SET” button to confirm your selection. “SELECT ID” appears on the display. 
5. Press and release the “▲“ or “▼“ buttons to cycle through the Monitors and/ or Sensors that the display has wirelessly identified. 
6. Press the “SET” button to confirm your selection. “SELECT NAME” appears on the display. 
7. Press and release the “▲“ or “▼“ buttons to cycle through the available location names. Select the name that most closely matches the location where the Sensor that is reporting data for the location is installed. 
8. Press the “SET” button to confirm your selection. The new Sensor will now synchronize with the display. It may take a few minutes for synchronization to complete. 

Important!

If you are pairing more than one temperature sensor with the display, the A-B-C switch positions must differ between each sensor. Verify that each sensor has a different channel selected by checking the switch position in the battery compartment.

The 12-24 hour future forecast feature requires a weather-resistant Monitor or Sensor (sold separately) to be placed outdoors and its location name must be set to OUTDOOR or GARDEN.

If you are still experiencing concerns, please contact our U.S. based support staff by Submitting a Request or by chatting with our Live Agents. If you already have an open ticket with a support agent, please reply to the last email sent.