Temperature is Frozen, Flashing, or Showing Dashes on Models 06024M and 06036M

Follow

 

  1. Remove the affected Location from the display.
  2. Press and release the color-coded button next to the location you want to delete from the display.
  3. Press and release the “SET"  button.
  4. Press and release the “▲“ or “▼“ buttons until “DELETE” is showing.
  5. Press and release the “SET” button. “DELETE MONITOR” will flash.
  6. Press and release the “SET” button to remove the location from the display.
  7. Remove batteries from the remote sensor/monitor only. Do not power down the digital display.
  8. Wait 1 minute.
  9. Reinstall the batteries in the remote sensor/monitor.

 

To sync model 00275/00276 with a 06024/06036 display follow the steps below: 

 

Confirm the sensor is powered on with a reading on the display (model 02076RM)  or having the red light flash every 16 seconds (02075RM)

  1. Press and release the color-coded button next to a location on the display with the name “AVAILABLE.” Next, “ADD MONITOR” will flash at the top of the display. 
  2. Press the “SET” button. “SELECT MONITOR STYLE” and (2) sensors will flash on the display. 
  3. Press and release the “▲“ or “▼“ buttons to highlight the larger square sensor located on the right. 
  4. Press the “SET” button to confirm your selection. “SELECT ID” appears on the display. 
  5. Press and release the “▲“ or “▼“ buttons to cycle through the Monitors and/ or Sensors that the display has wirelessly identified. 
  6. Press the “SET” button to confirm your selection. “SELECT NAME” appears on the display. 
  7. Press and release the “▲“ or “▼“ buttons to cycle through the available location names. Select the name that most closely matches the location where the Monitor or Sensor that is reporting data for the location is installed. 
  8. Press the “SET” button to confirm your selection. The new Monitor or Sensor will now synchronize with the display. It may take a few minutes for synchronization to complete. Please refer to the troubleshooting section of this manual if anything appears to be functioning improperly.

 

To sync model 00592TXR/06002M/06044M with a 06024/06036 display follow the steps below: 

 

Confirm the sensor is powered on with a reading on the display (model 06044M)  or having the red light flash every 16 seconds (06002M)

  1. Press and release the color-coded button next to a location on the display with the name “AVAILABLE.” Next, “ADD MONITOR” will flash at the top of the display. 
  2. Press the “SET” button. “SELECT MONITOR STYLE” and (2) sensors will flash on the display. 
  3. Press and release the “▲“ or “▼“ buttons to highlight the narrow tall sensor located on the left. 
  4. Press the “SET” button to confirm your selection. “SELECT ID” appears on the display. 
  5. Press and release the “▲“ or “▼“ buttons to cycle through the Monitors and/ or Sensors that the display has wirelessly identified. 
  6. Press the “SET” button to confirm your selection. “SELECT NAME” appears on the display. 
  7. Press and release the “▲“ or “▼“ buttons to cycle through the available location names. Select the name that most closely matches the location where the Monitor or Sensor that is reporting data for the location is installed. 
  8. Press the “SET” button to confirm your selection. The new Monitor or Sensor will now synchronize with the display. It may take a few minutes for synchronization to complete. Please refer to the troubleshooting section of this manual if anything appears to be functioning improperly.

 

Important!

If you are pairing more than one temperature sensor with the display, the A-B-C switch positions must differ between each sensor. Verify that each sensor has a different channel selected by checking the switch position in the battery compartment.

The12-24 hour future forecast feature. To forecast precipitation accurately a weather-resistant Monitor or Sensor (sold separately) must be placed outdoors and its location name must be set to OUTDOOR or GARDEN.

 

Was this article helpful?
1 out of 16 found this helpful